pogopin connector manufacturers!Antenna thimble company

　　It seems that a socket with a top-mounted connector is needed, because this setup can run tracking under the socket and is likely to facilitate the use of conformal paint. Some disadvantages of top-mounted sockets are that the width of the vacuum pick-up area is often narrow. There is no plastic shell material above the socket terminals to prevent the rise caused by rough disconnection. The more uneven top surface of the socket may be a connection work belt for the operator Come trouble.

　　These new pogopin connectors with stronger disconnection sounds great! Yes, but you may need to tolerate additional pogopin connector lengths in order to achieve the locking function required by these pogopin connectors; greater disconnection force usually also means greater engagement force, which may also be a larger size The circuit causes problems.

　　1. Test inspection of pogopin connector:

　　1) Observe that the loading voltage on the pogopin connector should not exceed 50% of its rated voltage.

　　2) Pogopin connector installation size For plug-in headers, the length of the soldering pins on the soldered PCB requires that the exposed part of the PCB is greater than 0.5mm.

　　3) For the more precise pogopin connector, if the PCB space permits, try to choose the model with a little positioning to facilitate the operation when manual soldering is required.

　　4) Check if there is a foolproof design

　　5) Check whether the material used in the pogopin connector contains lead.

　　6) Small size pogopin connector, low contact pressure, and low current and voltage applications, it is recommended to use gold-plated or silver-plated pogopin connector to avoid the film resistance from affecting the signal.

　　7) Pay attention to observe the height of the pogopin connector after mating, and whether it meets the soldering height of the components around the PCB. The mating height must be greater than the soldering height of the components around the PCB, and ensure that there is a certain margin to ensure that no interference occurs. Special attention should be paid to the possible height errors of the components after PCB soldering.

　　6. Connection problems and common troubleshooting

　　The correct connection of the pogopin connector product can increase the service life of the product and ensure the good operation of the mechanical equipment. If the product fails and is not handled in time, it will bring immeasurable economic losses. Here is a brief introduction to the connection and troubleshooting methods of the pogopin connector circuit.

　　1) About the connection problem of the pogopin connector

　　Plug and socket are used to electrically connect two circuit boards that are separated from each other.

　　A pogopin connector and a pogopin connector used to connect the pogopin connector in series, wherein the pogopin connector has a terminal connected to the circuit board and a body that accommodates the terminal. The adapter pogopin connector is provided with a second terminal and a body accommodating the second terminal. The two extended tail ends of the second connection terminal can be plugged and matched with the connection terminal to achieve the pogopin which is respectively arranged on the two circuit boards. The electrical conduction of the connector, wherein the end of one of the terminal and the second terminal is provided with an elastic part that is bent in the opposite direction, and the body and the second terminal can be appropriately extended according to the standard of the spacing of the circuit board length.

　　2) About pogopin connector troubleshooting

　　Once the product fails, the cause can be judged to be the wire breakage during use, the product loosening, etc. The frequency of wire breaking in the middle is not much, most of them are broken at the pogopin connector, so the focus of inspection should be on the sensor and the wires in the connection to see if they are loose and poor contact. Generally, open circuit failures caused by poor contact are mostly caused by rust at the end of the product, and external dirt enters the terminals or connection sockets, resulting in a decrease in contact pressure. To deal with this kind of failure, you need to remove the pogopin connector, plug it in again, and change its connection status to restore normal contact.　　 1. What is a pogopin connector?

　　The basic concept of pogopin connector is to connect different circuit boards together. It is the pogopin connector product with the strongest transmission capacity among all pogopin connector product types. It is mainly used in power systems, communication networks, financial manufacturing, Elevators, industrial automation, medical equipment, office equipment, home appliances, military manufacturing and other industries.

　　At present, the main pitches of pogopin connectors are 0.50mm, 0.60mm, 0.80mm, 1.00mm, 1.25mm, 1.50mm, 2.00mm, 2.50mm, 2.54mm, 3.96mm.

Read recommendations:

M2877 6.5X17.0(5A)Double-head Pogo Pin Merchant

M1802 2.0X5.0(2A)blunt probe company

M2109 2.0x24.15(1A)

How to choose the right Pogopin connector?Connector Processing

Pogo Pin charging head customized processing process